Accessories for Gas Warining Device X-am® 7000
CHF 160.90*
Content:
1
Delivery according to order confirmation
Product number:
7656801
Manufacturer:
Dräger Safety AG & Co. KGaA
* Specifications refer to the packaging unit
This device is the innovative solution for the simultaneous and continuous detection of up to five gases. A combination of more than 25 sensors allows flexible solutions to individual monitoring tasks. The device can be equipped with three electrochemical, and two catalytic bead, infrared or photoionisation sensors. It is the ideal companion in a great number of applications where reliable monitoring of oxygen, toxic and combustible gases and vapors in ambient air is necessary.
Basic unit with rubber-boot, carrying strap, calibration adapter, water and dust filter. In order to get a fully operational unit, a power pack and up to 5 sensors have to be ordered. And, optionally, a built-in pump or a datalogger can be ordered.
Basic unit with rubber-boot, carrying strap, calibration adapter, water and dust filter. In order to get a fully operational unit, a power pack and up to 5 sensors have to be ordered. And, optionally, a built-in pump or a datalogger can be ordered.
| Specifications | |
| Temperature: Pressure: Humidity: | -20 ... +55 °C, short-term -40 ... +60 °C 700 ... 1300 hPa 10 ... 95 % r.F. |
| Alarms (visual/audible): | 360° flashing LEDs / |
| Charging time: | 3.5 to 7 hours, depending on battery type |
| Pump mode: | maximum hose length of 45 m |
| Dimensions (W x H x D): | 150 x 140 x 75 mm |
| Weight (basic unit/battery): | 600 g / 490 g (3,0 Ah), 730 g (6,0 Ah) |
| Ingress protection: | IP 67 |
| Approvals: | ATEX, MED, CSA, IECEx |
| Manufacturer Article Number: | 8318169 |
|---|---|
| Type: | Car mounting kit |
Other customers also bought
Analox Sensor Technology Ltd.
Carbon Dioxide Safety Monitor AX60
Gas warning device for precise measurement of the amount of CO2 in the air. 3 alarm settings factory set: Time-weighted average (TWA) alarm (5000 ppm; 0.5% CO2), Low alarm (15,000 ppm; 1.5% CO2) and High alarm (30,000 ppm; 3% CO2)No calibration required (unless local regulations state otherwise)Very long life sensor can last up to 15 yearsUp to 4 x CO2sensors and 8 x CO2 alarms can be used per Central Display UnitSupplied with a relay on each alarm which can be used to trigger ventilation, extraction or a building management systemEasy installation and maintenance can be conducted by the userAdditional (quick connect) CO2 sensors and alarms available if more than one entrance to the laboratory or more than one risk areaAssists in compliance with Exposure Limit regulations such as EH40Scope of delivery: wall-mounted central display unit, CO2 sensor and CO2 alarm which can provide an early warning of a CO2 leak.Specifications:Range :
Accuracy :0.1 to 5 % CO2
+/- 5 % of alarm setpointAlarm intensity :88 dbAMonitor Display :16 digit 2 line LCD in ppmTWA Alarm :5,000 ppm (0.5 %) over 8 hoursCO2 Alarms :15,000 ppm (1.5 %) and 30,000 ppm (3 %)Operating Temperature :-5 to 50 °CCentral Unit Dimensions :175 x 110 x 75 mmSensor & Alarm Dimensions :72 x 170 x 45 mmIP Rating :IP55 (IP54 Central Display Unit)Warranty :5 years for electronics and sensor
Similar products
The Dräger-Tubes® measuring system is the safe method for measuring pollutants in the soil, water and air. More than 500 substances can be measured in varying concentrations. The long-established principle of Dräger-Tubes® is still the same. A defined volume of gas/air must be pumped through the sampling tube. This can be achieved by using the Accuro® gas pump. On contact with the substance under test the reagent system contained in the tube reacts and displays a colour. The strength of the concentration of the substance is shown by the length of the colour band displayed and can be read directly from the scale. The Dräger-Tubes® sampling system provides accuracy, efficiency, quick and easy handling. Over 250 tubes are available on request for all substances and measuring fields. Further sampling devices, diffusion tubes for long-term measurements as well as sampling systems with activated carbon tubes, ORSA collector and TDS thermodesorption tubes are also available.
In many fields, such as mining or industry, it is very important to detect even the smallest air flows, in order to quickly and reliably evaluate the possible diffusion of dangerous substances. With the air flow test tubes, the source, direction and speed of the air flow are visible immediately.
The Dräger-Tubes® measuring system is the safe method for measuring pollutants in the soil, water and air. More than 500 substances can be measured in varying concentrations. The long-established principle of Dräger-Tubes® is still the same. A defined volume of gas/air must be pumped through the sampling tube. This can be achieved by using the Accuro® gas pump. On contact with the substance under test the reagent system contained in the tube reacts and displays a colour. The strength of the concentration of the substance is shown by the length of the colour band displayed and can be read directly from the scale. The Dräger-Tubes® sampling system provides accuracy, efficiency, quick and easy handling. Over 250 tubes are available on request for all substances and measuring fields. Further sampling devices, diffusion tubes for long-term measurements as well as sampling systems with activated carbon tubes, ORSA collector and TDS thermodesorption tubes are also available.
Fast measurement with one hand: The Dräger-Tube pump accuro® allows you to use the established Dräger-Tubes® to take measurements under extreme conditions. The easy-to-use Dräger-Tubes have already been calibrated and form a perfect unit with the Dräger-Tube pump.Gas pump Dräger accuro® set consisting of:Dräger-Tubes® pump accuro®, ready bag, with tube opener and spare part set
The Dräger-Tubes® measuring system is the safe method for measuring pollutants in the soil, water and air. More than 500 substances can be measured in varying concentrations. The long-established principle of Dräger-Tubes® is still the same. A defined volume of gas/air must be pumped through the sampling tube. This can be achieved by using the Accuro® gas pump. On contact with the substance under test the reagent system contained in the tube reacts and displays a colour. The strength of the concentration of the substance is shown by the length of the colour band displayed and can be read directly from the scale. The Dräger-Tubes® sampling system provides accuracy, efficiency, quick and easy handling. Over 250 tubes are available on request for all substances and measuring fields. Further sampling devices, diffusion tubes for long-term measurements as well as sampling systems with activated carbon tubes, ORSA collector and TDS thermodesorption tubes are also available.
Transparent. With 1- or 3-way stopcocks, PP, with free-turning Teflon® plugs.SpecificationsCapacity:250 mlTube length:222 mmTube diameter:51 mmMaximum pressure:15 psiFor tubing with an internal diameter:6.4 .. 9.5 mmStopcocks:64 mm
The Dräger Aerotest Alpha allows the quality of breathing air supplied by a compressor or compressed gas cylinder to be determined. Use of the test system performs a reliable check in accordance with the breathing air standard EN 12 021.Dräger Aerotest Alphacomprising of 1 pressure reducer, measuring device for 4 tubes, impactor adapter, coupling, barbed nipple, stopwatch, tube opener Dräger TO 7000, bubble test hose, pack of 5 sintered filters, instruction for use, transport case (black)Dräger Aerotest Alpha, with Dräger Tubes :Dräger Aerotest Alpha+ box of 10 Dräger Oil Impactors,+ box of 10 Dräger-Tubes carbon dioxide (CO2) 100/a-P,+ box of 10 Dräger-Tubes carbon monoxide (CO) 5/a-P,+ box of 10 Dräger-Tubes water vapor (H2O) 20/a-PSpecificationsDimensions of carrying case (L x W x H)350 x 300 x 85 mmWeight, including contentsapprox. 3.0 kgMax. supply pressure
Supply pressure (set on delivery)15 bar
3.0 barPressure gauge0.3 to 15 barConnection for compressed air supplybarbed nipple 9 mmFlow rate0.2 and 4.0 l/min
The widespread use of N2, LN2, He or Ar in laboratories poses a potential asphyxiation hazard to personnel. If an inert gas leaks or builds up in a confined area it can deplete the O2 to dangerously low levels. The use of enriched O2in laboratories poses both a fire risk and hyperoxia risk to personnel if it were to leak or build up in a confined area.The O2NE+ and Safe-Ox+ from Analox Sensor Tecnhology are an affordable, low maintenance, long life solution to assist in mitigating the risk of using these gases in your laboratory.Long life, low drift sensor lasts up to 7 yearsMinimum calibration check required - only every 12 months (user maintainable)Simple to read "OK", "Alarm" and "Fault" indicationEasy installation and maintenance can be conducted by the userAdditional (quick connect) alarm repeaters available if more than one entrance to the laboratoryAssists in compliance with Exposure Limit regulations such as EH40Supplied with relays which can be used to trigger ventilation or building management systems etcSafe-Ox+™ is a simple to use, wall mounted oxygen enrichment and depletion monitor which has 2 audible/visual alarms which will trigger at 23% and 19.5% O2 which means that lab personnel can take evasive action in the event of a gas leak.Delivery Includes: Main O2 sensor unit with 2 relays and 1 alarm repeater to be placed at the entrance, with mains power supply.Specifications:Range :0.1 to 25 % O2Sensor Accuracy :+/- 0.75 % O2 (5.0 to 25.0 %)Alarm intensity :85 dbAMonitor display :4 digit LCDOperating Temperature :0 to 40 °CMonitor Dimensions :175 x 110 x 75 mmAlarm Repeater Dimensions :72 x 170 x 45 mmIP Rating :IP65 (IP43 alarm repeater)Warranty :2 years electronics (1 year sensor)