Insulating mantles KM-IRU series
CHF 611.00*
Content:
1
Delivery according to order confirmation
Product number:
4685036
Manufacturer:
ISOHEAT GmbH
Packaging information:
Weight:
1.25 kg
Description
Insulating mantles for single and double neck round bottom flasks. To prevent heat losses occuring at the upper flask halves.
- Made by hand work
- Aluminium coated outer jacket
- Thermally insulated
Properties
| Manufacturer Article Number: | 96403000 |
|---|---|
| UNSPSC: | 41-10-24-05 |
| Volume vessel: | 3000 ml |
| Ø vessel: | 185 mm |
Skip product gallery
Electronic heating mantles HM-200
From
CHF 564.00*
Standard heating mantles series KM-G
From
CHF 447.00*
Metal-cased heating mantles series KM-ME, with controller
From
CHF 242.00*
Electronic multi-size heating mantles HM-200-V, V-shaped
From
CHF 619.00*
Heating mantles Electrothermal® MHM-200
From
CHF 6,125.00*
Temperature sensors for Laboratory regulator series KM-RX
From
CHF 99.10*
Metal-cased heating mantles KM-MEB series
From
CHF 736.00*
Analogue heating contollers CN-200
From
CHF 501.00*
Similar products
Polypropylene outer case is resilient and chemically resistant. Highly efficient in heating up to a maximum element temperature of 450 °C. The flexible heating element is suspended in a thermal insulating cartridge to provide maximum heat transfer with minimum risk of flask breakage. Even at full power output, the exterior remains "cool-to-touch" due to good heating element insulation. All heating mantles have support clamp for rods of up to 12 mm diameter, and are double fused, with earth (ground) screen to protect the user from electric shocks.Spare heater cartridges are available on request.
LabHEAT®-Heating mantles for flasks, round bottom. Flexible glass yarn heating element, outer jacket in glass silk, with diam. 60 mm bottom out-let from 500 ml, max. heating element temperature 450 °C, 1.5 m power supply (earthed) cable with heating-zone switch and RCD (residual current detection).
LabHEAT® - Heating mantles for flasks, round bottom. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing with built-in power-on and heating zone switch, in addition equipped with a controller which allows a continuous adjustment of the heater power; max. heating element temperature 450 °C; 1.5 m power supply (earthed) cable and RCD (residual current detection).
Solid, with mesh stainless steel liner, which protects against fluid spills, with central aperture to accommodate round-bottom and pear-shaped flask and 60° funnels. For round bottom flasks, pear-shaped flasks and 60° funnels (Mantle is open at the bottom). Polypropylene outer case is resilient and chemically- resistant. Highly efficient in heating up to a maximum element temperature of 450 °C. Even at full power output, the exterior remains "cool-to-touch" due to good heating element insulation. All heating mantles have support clamp for rods of up to 12 mm diameter, and are double fused, with earth (ground) screen to protect the user from electric shocks.Spare heater cartridges are available on request.
Heating mantle has a "V"-shaped design for large, pear-shaped and round-bottom flasks. The bottom opening allows 60° funnels of various diameters to be accommodated. Coiled heating element provides optimal heat transfer. Control heat throughout the mantle using three separate electrical circuits (top, middle, and bottom), each controlled with its own dial switch.Cool-to-the-touch design with powder-coated aluminium casingIndicator lamps for "power on" and "heat on" operationScope of supply: Heating mantle, three sets of integrated support rod clamps, power cords with UK and EU plugs
LabHEAT®-sensors. Suitable for temperature control and KM-KM-RX1001 RX1004 with permanently attached cable, with or without diode plug.KM-TP2: Pt100, up to 400 °C, sheated element V2A, dia. 4 x 50 mm,KM-TPG: Pt100, up to 250 °C, glass tube, dia. 6 x 40 0mm,KM-TNS: NiCr-Ni, up to 1200 °C, rod sensor in Inconell, dia. 1.5 x 300 mmKM-TNF: NiCr-Ni, up to 400 °C, flat sensor, 0.4 x 15 x 400 mmFurther models available on request.
With corrosion-resistant stainless steel heating bowl to protect against leaking liquid resulting of a broken flask.Increased working safety in the labPlastic-coated, chemically resistant metal housingPredrilled threaded hole on rear allows to fix the stativ clamp2 heating zonesWith built-in controller allows a continuous adjustment of power outletThermally insulated and earthedWith built-in heating zone switch and residual current detection (RCD)
For power control of heating mantles of the HM series, electric Bunsen burners and heating tapes. Each controller has two neon indicators: White neon "Power On" and amber neon "Mantle/Bunsen Heater On". When the control knob is turned clockwise, the power increases and the amber indicator light begins to pulse. As soon as the maximum power is reached, the lamp lights up continuously. There is a clamp on the rear of the controller for attaching a rod (Ø 12 mm).